Innovation! Delivery December 2024

Pre-order deadline: 2/26/2024

• with DCC Decoder
• with Sound

Road Number-Specific ScaleTrains All-new model Era: 1960s-1970s Series 3010 to 3029, built Sep/Oct 1967 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated Pyle-National (Translite) #20585 “Gyralite” dual signal light mounted in number board housing* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets Printed number boards with separately-controlled, backlit LED-illumination* “Late” MU hose catch box, front and rear 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Front and rear straight uncoupling levers without loop handles MU Receptacles “Late” tall deck-mounted multiple-unit (MU) receptacles, front and rear “Tall” stepwells with “zig-zag” pilots, front and rear End handrails with deck and pilot face-mounted stanchions, front and rear Front and rear early small deck extension Positionable tapered (early) drop steps, front and rear Late treadplate 81” low short hood without handbrake Late drop grabs and standard nut-bolt-washer (NBW) mounting on nose front and top Early cab sub-base doors with terminating reinforcement ribs, both sides Dual right rear cab steps Early cab step guards (long taper) No hopper water piping underneath front battery box step Standard EMD low headlight in face of short hood “35-Line” cab with standard front windshields, and standard armrests, both sides Detailed cab interior with separate floor, cab blowers, rear wall, early seats, and standard AAR control stand Positionable cab side windows No mirrors/windwings No sunshades or sunshade tracks Lost-wax cast brass Leslie S-3-LR horn mounted on number board housing Motorola ASP-16 “Firecracker” communications antenna mounted to cab roof Long hood with standard electrical cabinet seam, bolted generator compartment door, and early inertial drain hole placement (wide spacing on engineer’s side, low on fireman’s side) Small ECAFB Early (smooth) blower duct housing Early long handrail stanchion spacing with “short” stanchions at thin section of sidesill Early inertial air intake grilles without drip rails Standard turbo exhaust stack Early extended-range dynamic brake housing (short tapers) See-through 48” standard-height dynamic brake fan housing with 10-blade fan and hub assembly, with concentric-ring grill Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Diamond-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Early rear sander door catch placement (inboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at stepwell ends of trucks Rust-color painted wheelsets GE-brand speed recorder with adapter flange mounted to left #1 axle Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 2600-gallon fuel tank with early mounting brackets, tall sight glasses on front of tank, and early rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DCC & sound-equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” functions Two (2) cube-type speakers Turbocharged EMD 16-645 prime mover sounds ESU designed “PowerPack” with two super capacitors**** Operates on both DC and DCC layouts