新商品! 到貨於 十二月 2024

預定截止日期：2024/2/26

• 與DCC的使用（DCC接口）

Road Number-Specific ScaleTrains All-new model Era: 1970s-era Series 3086 to 3093, built Nov/1971 D&RGW 3087, 3088, 3089, 3090, and 3093: EMD square-corner “Burnham” number boards D&RGW 3092: Original EMD number boards Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors, and round walkway light aft of raised walkway duct* LED-illuminated Mars SBW-2-301 dual signal light (clear lenses) mounted in low short hood* LED-illuminated tri-color, flush-mounted front and rear class lights with raised gaskets Printed number boards with separately-controlled, backlit LED-illumination* Front EMD low plow with MU hose doors 3-hose multiple unit (MU) hose groups with mounting bracket and gladhand detail Semi-scale coupler buffers equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles Square-corner pilot face with angled lifting slots, front and rear “Late” tall deck-mounted multiple-unit (MU) receptacles, front and rear “Tall” stepwells with “zig-zag” pilots, front and rear End handrails with deck-mounted stanchions, front and rear Front and rear early small deck extension Positionable straight (late) drop steps, front and rear Late treadplate 81” low short hood with ratchet handbrake Late drop grabs and standard nut-bolt-washer (NBW) mounting on nose front and top Latched battery box doors with narrow louvers and tab-style (early) hinges Early cab sub-base doors with non-terminating reinforcement ribs, both sides Dual right rear cab steps Late cab step guards (short taper) Hopper water piping underneath front battery box step Standard EMD high headlight with glare visors in numberboard housing “35-Line” cab with standard armrests, and flag holder bracket on right side (D&RGW) Detailed cab interior with separate floor, cab blowers, rear wall, early seats, and standard AAR control stand Positionable cab side windows Tall square-corner clear wind wings mounted fore and aft of cab side window, both sides of cab Standard EMD sunshades with long mounting tracks Lost-wax cast brass Nathan AirChime M3 (M3R1) horn mounted on number board housing Excalibur low-profile “ice skate” communications antenna mounted to cab roof Long hood with standard electrical cabinet seam, bolted generator compartment door, and late inertial drain hole placement (close spacing on engineer’s side, high on fireman’s side) Small ECAFB Late (ribbed) blower duct housing Late long handrail stanchion spacing with all “tall” stanchions overall Early inertial air intake grilles without drip rails Standard turbo exhaust stack Late standard-range dynamic brake housing (long tapers), with rectangular vent See-through 48” dynamic brake fan housing mounted on riser ring with 10-blade fan and hub assembly, with concentric-ring grill Dynamic brake intakes with see-through intake vanes, and resistor grid detail inside of the housing Rectangular-mesh radiator intake screening See-through standard-height 48” radiator fan housings with 8-blade fan and hub assembly Separately-applied radiator core detail mounted inside of long hood, visible under radiator fans Curved radiator fan grab iron Rear LED-illuminated horizontal headlight and standard housing Late rear sander door catch placement (outboard) Underbody frame rails with separately-applied plumbing and traction motor cable bundle details Detailed Blomberg-B truck frames (LFM-cast) with Hyatt bearing housings, separately-applied brake cylinders in released (piston retracted) position, elliptical springs, end transom detail, separate sanding lines and brackets, and separate swing hanger detail Separately-applied flexible neoprene sanding lines at both ends of trucks Rust-color painted wheelsets Early EMD speed recorder mounted to right #1 axle “McCarty” type re-rail frogs ACI labels mounted to blower duct on left side, and rear cab step kickplate on right side Standard 4 jacking pads Frame-mounted bell Salem-brand #824-170 and #818-170 primary and secondary centrifugal air filters, respectively (accordion-style) Separately-applied brake vent regulator valve and plumbing detail on underbody 3600-gallon fuel tank with late mounting brackets, inset dial gauge on both sides, and late rear drain bar Separately-applied fuel fillers, drains, and breather piping on fuel tanks Separately-applied engine oil sump drain fitting with hose Separately-applied radiator water drain fitting on underbody Separately-applied truck air line plumbing on underbody above each truck, both sides Separately-applied wireform grab irons, wireform lift rings, etched windshield wipers, trainline hoses, sand hatch covers, and more Motor with 5-pole skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended Radius: 22” DC/DCC & sound ready locomotives also feature: Operates on DC layouts DCC-ready with 21-pin connector