- 14V Gleichstrom Netzteil oder Spannungswandler 110V/220V wird benötigt, liegt nicht bei

Overcome programming problems with BLI, Soundtraxx and multiple decoder/loco combinations. Microprocessor controlled unit safely boosts and controls programming power to about 200 mA. When hooked up for programming, unit initially powers programming track to charge-up decoder components like capacitors that would otherwise reduce programming energy and cause a programming failure. Built-in circuit protection, with LED indicator, shuts down instantly in the event of an overload or short to protect the decoder and system programming circuits. Compatible with Broadway Limited locos, Digitrax, Lenz, MRC, NCE, TCS and Soundtraxx decoders in both single and dual decoder configurations and also works with programming software, RR&Co (Train Programmer) and JMRI (Decoder Pro), all sold separately.

Fits E24 socket locomotives N-Scale Mobile Decoder 13 FX3 Functions, 200mA capacity Motor drive at connector capacity

Fits many older Atlas N locomotives Mobile Decoder Drop in “A0” Atlas light board replacement decoder 1.0 Amp/2 Amps Peak 4 FX3 Functions, 200ma output

Fits many Kato N-locomotives Drop-in light board replacement decoder for Kato “K1” form-factor boards 1.0 Amp/2 Amps Peak 4 FX3 Functions, 200ma output Replaces both the DN163K1C & DN163K1D

Fits many Kato N-locomotives Drop-in light board replacement decoder for Kato “K2” form-factor boards 1.0 Amp/2 Amps Peak 4 FX3 Functions, 200ma output

Fits many Kato N-locomotives Drop-in light board replacement decoder for Kato “K0” form-factor boards 1.0 Amp/2 Amps Peak 6 FX3 Functions, 200ma output

Fits many Kato N-locomotives Drop-in light board replacement decoder for Kato “K0” form-factor boards 1.0 Amp/2 Amps Peak 6 FX3 Functions, 200ma output

5er Pack 9 Pin Dummy Plugs mit Lichtumschaltung in Fahrtrichtung. Wird benötigt beim Ausbau des Decoders um die Lok analog fahren zu lassen.

5er Pack, 9 Pin Stecker mit Kabel (Decoderanschlusskabel)

Kabel mit 9 Pin Stecker (passt in Digitrax Decoder) auf DCC Normstecker (für Loks mit DCC Schnittstelle nach NEM 652).

Kabel mit 9 Pin Stecker (passt in Digitrax Decoder) auf DCC Normstecker mit kurzem Kabel (für Loks mit DCC Schnittstelle nach NEM 652).

* This 2 function FX3 decoder is designed to fit KATO NW2. 128 Speed Step operation (14 or 28 steps can also be used). Momentum with acceleration and deceleration. Normal Direction of Travel is user selectable. 3 Step Speed Tables set start, mid and max voltage for custom control. 28 Step Speed Tables with 256 level resolution for precise control. SuperSonic™ motor drive for silent operation. FX 3 Function outputs for prototypical lighting effects and on/off control: Constant Brightness Lighting with directional or independent control FX 3 & Standard Function Qualifiers operate functions based on direction, F0 on or off, direction and F0, and whether loco is moving. Function Remapping for custom function setup. Decoder Lock equipped * All Mode Programming with Operations Mode Read Back reads back CV values right on the mainline. * Decoder Reset CV with or without speed table reset. * Motor Isolation Protection prevents damage to your decoder. * Basic, Advanced & UniVersal Consisting * 2 Digit and 4 Digit Addressing * DCC Compatible * FCC Part 15, Class B RFI compliant Current Rating 1.00 Amp (2.0 Amps Peak)

•Series 6 Features •2 FX3 Functions •10.63mm x 15.79mm x 2.72mm •Fits MicroTrains Line SW1500 units

Tiny Super Economical Motor & Function Decoder * Fits many N and HO Scale Locomotives * Digitrax N Scale Harness and Plug arrangement for economic decoder sharing options * 13.86mm x 10.3mm x 4.83mm * 3 FX3 Functions * 1 Amp Continuous/1.25 Amp Peak Rating * Full Digitrax Series 5 mobile decoder feature set 13.86mm x 10.3mm x 4.83mm Installation Digitrax Easy Connect 8-pin Harness Function Outputs 4-500mA Function Type FX3 Features Series 3

Tiny Super Economical Motor & Function Decoder * Fits many N and HO Scale Locomotives * Digitrax N Scale Harness and Plug arrangement for economic decoder sharing options * 13.86mm x 10.3mm x 4.83mm * 3 FX3 Functions * 1 Amp Continuous/1.25 Amp Peak Rating * Full Digitrax Series 5 mobile decoder feature set 13.86mm x 10.3mm x 4.83mm Installation Digitrax Easy Connect 8-pin Harness Function Outputs 4-500mA Function Type FX3 Features Series 3

Für Kato N RDC - 3-teiliger Decoder mit Lampen

Current Rating 1.00 Amp (1.5 Amps Peak) Installation 3 part decoder with main body connected to two lamp boards Function Outputs 2-125mA Function Type FX Features Premium

Torque Compensation for smooth as silk silent operation. 128 Speed Step operation (14 or 28 steps can also be used). Momentum with acceleration and deceleration. Normal Direction of Travel is user selectable. Switching Speed feature for easier and faster access to yard speeds. 3 Step Speed Tables set start, mid and max voltage for custom control. 28 Step Speed Tables with 256 level resolution for precise control. N Scale Mobile Decoder 1.25 Amp/2 Amp Peak 4 FX 3 Functions, 0.5 Amp Current Rating 1.25 Amp (2.0 Amps Peak) Size 29.43mm x 9.81mm x 2.98mm Installation Wired Function Outputs 4-500mA

Board replacement decoder for Atlas N-Scale GP40-2, U25B, SD35, Trainmaster, B23-7 and others Current Rating 1.00 Amp (2.0 Amps Peak) Size 0.374 x 3.0015 w/LEDs x 0.1570 9.5mm x 76.2mm x 4.0mm Installation Board replacement decoder Function Outputs 6-500mA

Board replacement decoder for Atlas N-Scale SD60, SD60M, SD50 and others Current Rating 1.00 Amp (2.0 Amps Peak) Size 0.374 x 3.875 w/LEDs x 0.1570 9.5mm x 98.3mm x 4.0mm Installation Board replacement decoder Function Outputs 6-500mA

Board replacement decoder for Atlas MP15 units Golden-White LEDs for added realism Decoder Lock equipped Current Rating 1.00 Amp (2.0 Amps Peak) 0.3 x 3.875 w/LEDs x 0.1570 Size 9.5mm x 98.3mm x 4.0mm Installation Board replacement decoder Function Outputs 6-500mA Function Type FX3 Features Series 3