You are here:
Item #: SXT38811
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
New roadname Era: 1980-1989 ICG Series 6040-6049; ex-Rock Island 4790-4790, built 12/1973 Fully-assembled LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors and round walkway light, aft of raised walkway duct* LED-illuminated Power Parts Company PPC-11200 Oscitrol signal light with dual clear and single red lenses mounted on number board housing LED-illuminated front tricolor stand-off class lights; flush-mounted rear class lights with raised gaskets*** Printed number boards with separately-controlled, backlit LED-illumination* Front EMD-style low pilot plow with multiple unit (MU) hose doors and grab irons 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers with loop handles and four inner mounting brackets Notched pilot faces with low angled lifting slots Deck-mounted multiple unit (MU) receptacles "Tall" stepwells with see-through steps Front and rear early small deck extension Handrail set with inward-facing stanchion mounting brackets, and gangway chain Front and rear standard drop steps Scale sectioned treadplate detail on walkways 81” low short hood with ratchet handbrake and angled chain guard Bolted battery box doors with narrow louvers Early cab sub-base doors with early hinges Standard EMD headlight mounted in low short hood Dash-2 cab with 11-bolt (top and bottom) side window panels Rectangular vent on right cab side Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Sliding cab side windows Tall clear wind wings with mirror, mounted fore of cab side window on both sides of cab Standard EMD sunshades with long sunshade tracks Lost-wax brass Nathan P-5 (P345R12) horn mounted on number board housing Motorola ASP-16 “firecracker” antenna mounted on the cab Accurate hood door and long hood detail Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Early inertial air intake grilles without drip rails Standard turbo exhaust stack Non-dynamic brake housing with batten strip See-through dynamic brake intakes with resistor grid detail “Chicken-wire” radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Curved radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, early center axle snubbers, sanding lines and brackets, and D-77 traction motor and air duct details Dimensionally accurate truck centers GE speed recorder with adapter flange mounted to first axle on left front Rearward-facing handbrake chain mount for HT-C trucks Tall jacking pads with holes (early) Forward engineer’s side sidesill notch Tab-mount EFCO Frame-mounted steel bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) 4,000-gallon fuel tank with fuel fillers, vertical gauges, round gauges in tank sides and vertical breather pipe Factory-applied wire grab irons, wire lift rings, windshield wipers, trainline hoses with silver gladhands, sand hatch covers, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 70, 83 and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22”
shipping weight: 1,320 kgItem #: SXT40743
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40744
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40745
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40746
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40747
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40748
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40749
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40750
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40751
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40752
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40753
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40754
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40755
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40756
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40757
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40758
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40759
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40760
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kgItem #: SXT40761
(incl. tax plus shipping)
Notice:
This product is not a toy. Not suitable for children under 14 years.
Innovation! Delivery September 2025
All-new model New roadname New paint scheme New road numbers Era: Early-Late 1960s Series 450-457, ex-775-781 built June 1953 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated walkway lights on hood ends * LED-illuminated, tri-color front and rear, door-mounted class light housings (SD7)** Printed and LED-illuminated number boards* Equipped with ATS cabinet on right front walkway High short hood and long hood end number boards 4-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale “cast” style coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Front and rear straight uncoupling levers without loop handles As-delivered pilot faces without uncoupling lever loop notches Pilot-face mounted MU receptacle and field loop receptacle, left side, and blanked receptacles, right side Standard SD7 stepwells (inset top and middle step) with poling pockets “Pipe” style handrail stanchions with end gangways with chain Front and rear standard drop steps Scale sectioned treadplate detail with EMD “dot” style pattern Standard high short hood Standard sub-base Standard sidesills with louvered access doors on right side Early-style EMD LED-illuminated headlight housing with lenses, front and rear Cab with large UP-style type armrests Detailed cab interior with separate floor, rear wall, seats, and early control stand, long-hood forward operation Sliding cab side windows Small mirrors mounted fore of cab side windows on both sides of cab UP canvas sun awnings Lost-wax brass cast Leslie RS-3-L horn mounted to long hood behind cab No radio antennas Standard bolted electrical cabinet roof hatch Separately-applied, UP-style extended exhaust stacks Dynamic brake housing with dual 36” fans Separately-applied photoetched radiator intake screens with intake shutters underneath See-through 36” fan housings with separate fans, radiator core detail, and hood roof plumbing Winterization hatch over #1 radiator fan Separately-applied sand fill hatches Detailed EMD Flex-i-Coil “C1” trucks with separately applied brake plumbing, brake cylinders, and flexible neoprene rubber sanding lines Dimensionally accurate truck centers Standard EMD bell mounted to bracket on non-dynamic housing. Underbody air filter details Single 1,200-gallon fuel tank mounted to the rear with dual staggered sight glasses per side, and single 1,200-gallon fuel tank to the front Factory-applied wire grab irons, end ladders, photoetched lift rings, windshield wipers, trainline hoses with silver gladhands, signal hoses with silver gladhands, air tanks with plumbing, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED-illuminated headlights Printing and lettering legible even under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound-ready locomotives also feature: Operable on DC layouts DCC-ready with 21-pin connector
shipping weight: 1,320 kg