- 14V Gleichstrom Netzteil oder Spannungswandler 110V/220V wird benötigt, liegt nicht bei

Overcome programming problems with BLI, Soundtraxx and multiple decoder/loco combinations. Microprocessor controlled unit safely boosts and controls programming power to about 200 mA. When hooked up for programming, unit initially powers programming track to charge-up decoder components like capacitors that would otherwise reduce programming energy and cause a programming failure. Built-in circuit protection, with LED indicator, shuts down instantly in the event of an overload or short to protect the decoder and system programming circuits. Compatible with Broadway Limited locos, Digitrax, Lenz, MRC, NCE, TCS and Soundtraxx decoders in both single and dual decoder configurations and also works with programming software, RR&Co (Train Programmer) and JMRI (Decoder Pro), all sold separately.

Ausschließlich für Kato-Weichen!

DS51K1 Stationary Decoder For Single Kato Unitrack Turnouts * Easy to use * Cost effective control for a single Kato Unitrack turnout or other similar device * Rated at amp. Great for HO & N Scale * Small size .319 x .509 x .152(8.11mm x 12.94mm x 3.88mm)

Loconet Universal Kabel 6adrig, z. Bsp. zum verbinden von UP5 und anderen Digitrax Komponenten. - RJ12 Stecker - RJ12 Stecker - voll belegt - Stecker: 6polig - Länge: 3 m

Günstiger vierfach Blockbesetztmelder zum Anschluss an DS54 oder SE8C zur Datenübermittlung an das Loconet.

Programierbarer Loconet Universal Gleisbesetztmelder für 16 voneinander unabhängigen Eingängen. Wird auch als Basisgerät für RX4 Transponding Empfängern verwendet.

BXP88 makes adding detection and transponding to your layout easier than ever. No more complicated wiring! •DCC Occupancy Detection supports up to 8 Detection Sections letting you know when equipped rolling stock is in a detection section on your layout. •One Transponding Zone per Detection Section lets you know the location of transponder-equipped locos or rolling stock. •Intelligent Automatic short-circuit and over-current power management for each Detection Section, improves reliability by avoiding most booster fault shutdowns. •Connects to LocoNet to transmit Detection Section occupancy, Transponding and track power information. •Detects any powered locomotives in a Detection Section. •Identify where specific rolling stock is on your layout with Digitrax transponder-equipped locos and rolling stock. •Detects rolling stock equipped with resistor wheel sets. •Plug and Play with Digitrax DCC systems with automatic Railsync polarity detection. •LED output headers for front panel indication of Detection Section occupancy, Transponding, and power status. •Easy-connect pluggable track wire terminal blocks can plug-in straight or at right angles. •3 Amp capacity per Detection Section , 8 Amp total unit capacity. •Automatically updates status at track power on. •Operations Mode Read Back allows you to read CV values of decoders equipped with transponders when on track. •Firmware update capability via IPL over LocoNet.

DM-1 Leistungsverstärker zu DS54 für motorische Weichen z. Bsp. Kato, LGB usw. Lampen u. a. bis 0,5 A

Vierfach Magnetartikeldecoder für ALLE Doppelspulen- (Märklin, Peco, Atlas, Roco usw.) oder Motorweichen (Feather, Tortoise usw.), Anleitung in Englisch. - Einfach zu installieren - Steuert 4 Weichen - für Weichen mit Motor- und Magnetantrieb - LocoNet Control - Stromaufnahme vom Gleis oder separater Booster - DCC Norm

Eight 9G servo decoder for 2-position Slow-motion turnouts. Configurable to control eight 3-position semaphores. Works with compatible LocoNet Systems. Plug and play connections. Option setup switches for configuration. On-layout remote programmability via LocoNet. 16 System Routes, with EZ-Route setup. Routes remotely editable using DT602 with latest software. 16 input lines for Switch and Detection inputs. Optional 16 direct hardware Route triggers. Software field update/IPL over LocoNet. DC 2mm 12V jack for reliable power input. Supports two DSXC4 input connector boards and cables. Supports two BD4N’s for block detection reporting. Supports 8 DSXCP1 Fascia control and direction indicators. Supports DSXCP1 indicating ‘servo in motion’. Optional DCC track input for limited feature capabilities.

Eingangsverbindungsplatine für DS74. Bietet Plug-and-Play-Konnektivität für DS74-Eingänge. Input interconnect board for DS74. Provides plug and play connectivity for DS74 inputs. Supplied with ribbon cable to plug into DS74 10 pin Input header. Allows plug-in of up to 4 DSXCP1 fascia controls. Direct ribbon cable plug-in header to BD4N detectors. 8 pin screw terminal plug for optional wire access to 8 input lines.

Armaturenbretthalterung Schaltersteuergerät. Verdrahten Sie das DS74-Eingangskabel oder verwenden Sie DSXC4 für Plug-and-Play. Fascia mount Switch control device. Wire to DS74 input cable, or use DSXC4 for plug and play. Two color leds display current Switch state. Supplied with 3 wire control cable.

9G mini servo system for turnout or motion control. Under layout mounting bracket included. Compact install for tight N scale switches, and decks. Includes pre-formed drive wires. Supplied with mount hardware.

Weitere Infos auf und Sounds zum downloaden: www.digitrax.com/sounddepot.php

The PR4 makes decoder programming and interfacing your layout and computer easier than ever. The PR4 seamlessly switches between computer interface and decoder programming modes automatically without having to press any buttons. The PR4 is electrically isolated between USB and LocoNet for added stability and protection. Packaged in a smaller footprint the PR4 offers all the same great features as the PR3 it replaces. Mit dem PR4 Decoder Programmer und SoundLoader Software, in Verbindung mit PC und Programmiergleis können Sie: - Sound nach Ihren Wünschen verändern - Sounds downloaden - testen - CVs umprogrammieren - SoundLoader Software zum Download auf der Digitrax Webseite Im Kit enhalten sind: - PR4 Programmer - USB Schnittstelle Benötigt wird: - 12-15V (DC) Gleichstrom Netzteil - PC mit Windows XP - Programmiergleis - Windows XP, Vista and 2000. - Mac OS 10.4/10.5 mit JMRI. Sounds von www.digitrax.com/sounddepot downloaden und mit dem Digitrax Programmer aufspielen: AC4400 SD38-2 F40PH GE Evolution Traction/Trolley SD70 Western Pacific #1983 British DMU Class 108 British Class 37 BritishLight-Prairie 2-6-2 44XX British �Yorkshire� switcher U33 RDC Bells and Whistles GP10 #7562 Union Pacific Challenger #3985 SW1 #4741 E8 Southern #6900 SW1C #4742 ALCO RS32 #30 Fairbanks Morse 1244 Switcher SD40-2 GP38 C44-9 weitere folgen in Kürze.

RD2 Remote Sensing Diodes for BDL16 & BDL168 Remote sensing of 2 detection sections. Eliminates the need for long runs of heavy gauge wire between the BDL16 & remotely located track sections.

4-fach Transponding-Empfänger für BDL168 Blockdetektor. Verwenden Sie den RX4 um den BDL168 mit Zugsnummernerkennung auszurüsten.

The Digitrax Signaling System is organized around the concept of security elements which are similar to what U.S. prototype railroads call plants. The Digitrax SE8C signal decoder displays aspects for up to 32 heads for 8 individual security elements (plants) using either a LocoNet Throttle or a computer with compatible software. When used with associated occupancy detectors and compatible software, the SE8C can be set up to protect the turnout as shown by the example below. The SE8C decodes switch commands from a throttle or associated software so that the appropriate aspects are displayed on the signal heads. Each security element is made up of three legs designated A, B, & C. Every piece of track on your layout can be broken down into security elements to describe how each detection section connects to the other sections on your layout. Digitrax Plug-n-play Signaling technology was awarded Model Railroader's 2003 Reader's Choice Award.

Material zum herstellen von 2 Signal Driver Kabeln für SE8C (ca. 9 m Kabel und 8 10 Pin Sockel).

Aus den Signalmast Kits, lassen sich in Verbindung mit Signalteilen anderer Hersteller Signale herstellen.

3er Pack, an jedem Mast sind 2x 3 LEDs angebracht.

Zum befestigen der Signal Kits.